Why Are Shielded Deep Groove Ball Bearings Ideal for High Speed?

2026-11-11

A motor repair shop replaces a set of Deep Groove Ball Bearings on a high speed spindle. The original bearings were open type. The technician installs rubber sealed bearings because the spindle operates in a dusty workshop and the seals will keep the dust out. After two hours of running, the bearing housing temperature rises from 35 degrees Celsius to 70 degrees Celsius. The grease turns dark, and the spindle vibration increases. The technician replaces the rubber seals with metal shields, and the temperature returns to 40 degrees Celsius. The difference is the friction of the seal lip against the inner ring. At high speed, that friction becomes the dominant heat source. This guide explains why shielded bearings are ideal for high speed applications.

6201RS Double Row Deep Groove Ball Bearings


1. Why Does Friction From Contact Seals Become the Limiting Factor at High Speed?

A contact seal has a rubber or synthetic lip that presses against the inner ring. The lip maintains contact at all speeds to keep contaminants out. The contact pressure creates a friction torque that is roughly constant at low speed but grows with speed because the sliding velocity at the lip increases. The friction power, which is the product of the friction torque and the angular velocity, grows with the square of the speed. At 3,000 RPM the heat is manageable. At 15,000 RPM the heat can exceed the grease's ability to dissipate it, and the bearing overheats. In our factory, we measure the friction torque of every seal and shield design on a torque test rig. Cixi Hengji Bearing Co., Ltd. has been manufacturing Deep Groove Ball Bearings for over 12 years.

The contact seal is not defective. It is designed for a different duty. A contact seal is the right choice when the environment is wet or heavily contaminated and the speed is moderate. A shielded bearing is the right choice when the speed is high and the contamination is dry dust or light debris. The two designs are not interchangeable without checking the speed rating.


2. How Does the Non-Contact Shield Reduce Friction Torque and Heat Generation?

A shield is a thin metal disc that is pressed into the outer ring and extends inward toward the inner ring. It does not touch the inner ring. The gap between the shield and the inner ring is typically 0.1 to 0.3 millimeters. Because there is no contact, the shield does not generate lip friction. The only friction is the churning of the grease inside the bearing. The shield still provides a physical barrier against large particles and reduces grease leakage. The table below compares the two designs.

Parameter Contact seal Metal shield
Friction torque High (lip contact) Low (no contact)
Temperature rise at 15,000 RPM 30 – 45°C 8 – 15°C
Maximum speed (relative) 1.0 (baseline) 1.8 – 2.2
Dust protection Excellent (wet and dry) Good (dry dust only)
Grease retention Excellent Good
Typical application Wet, dirty, low speed High speed, dry dust

The gap size is a trade off. A smaller gap improves the dust protection but increases the risk of contact if the bearing deflects under load. A larger gap reduces the risk of contact but allows more dust to enter. In our factory, we set the gap at 0.15 to 0.20 millimeters for most high speed applications. Cixi Hengji Bearing Co., Ltd. inspects the gap on every production lot with a feeler gauge.


3. What Role Does Grease Fill Volume and Base Oil Viscosity Play at High RPM?

The grease inside a shielded bearing is trapped for the life of the bearing. The fill volume and the base oil viscosity determine the churning loss and the lubrication film. If the bearing is overfilled, the grease churns, generates heat, and may channel or separate. If the bearing is underfilled, the raceway may starve and wear. The correct fill volume for a high speed bearing is 20 to 30 percent of the free space, compared with 40 to 60 percent for a low speed bearing. The base oil viscosity must be low enough to keep the churning loss low but high enough to maintain the film at the operating temperature. The table below shows the recommended fill volume and viscosity for different speed ranges.

dn value (mm x RPM) Grease fill volume Base oil viscosity at 40°C Expected temperature rise
50,000 – 100,000 30 – 40% 68 – 100 cSt 15 – 25°C
100,000 – 200,000 25 – 30% 46 – 68 cSt 12 – 20°C
200,000 – 400,000 20 – 25% 32 – 46 cSt 8 – 15°C
> 400,000 15 – 20% 22 – 32 cSt 5 – 12°C

Bearing application engineer's note: The dn value is the bore diameter in millimeters multiplied by the speed in RPM. It is the standard way to compare the speed severity of different bearing sizes. A 20 millimeter bore bearing at 20,000 RPM has a dn value of 400,000, which is a high speed application. The grease fill volume and the base oil viscosity must be selected for that dn value, not for the bore size alone. In our factory, we select the grease and the fill volume for each high speed order and we provide the grease data sheet with the shipment. Cixi Hengji Bearing Co., Ltd. stocks high speed greases with different base oil viscosities.


4. Why Do Cage Design and Internal Clearance Decide Whether the Shielded Bearing Survives High Speed?

The cage holds the balls in position and separates them. At high speed, the cage experiences centrifugal force that pushes it against the outer ring. A pressed steel cage can deform under high centrifugal force. A machined brass cage or a nylon cage is more stable at high speed. The nylon cage also has a lower mass, which reduces the centrifugal force. The internal clearance is equally important. At high speed, the inner ring heats faster than the outer ring, and the clearance decreases. If the initial clearance is too small, the bearing preloads itself and overheats. A C3 or C4 clearance is usually required for high speed applications. In our factory, we measure the clearance of every bearing after assembly and we match the cage material to the speed rating. Cixi Hengji Bearing Co., Ltd. offers pressed steel, nylon, and machined brass cages for our Deep Groove Ball Bearings.

The shield must also be compatible with the cage. A shield that is too close to the cage can rub against it at high speed. We check the shield-to-cage clearance during the assembly inspection.


5. How Should Engineers Specify and Verify Shielded Bearings for High-Speed Applications?

The specification should include six items. The first is the speed or the dn value. The second is the clearance group, C3 or C4. The third is the cage material. The fourth is the grease type and the fill volume. The fifth is the shield type, metal shield or rubber seal. The sixth is the noise and vibration requirement. The verification should include four checks. The first is the clearance measurement. The second is the shield gap measurement. The third is the temperature rise test at the rated speed. The fourth is the vibration test. In our factory, we perform these checks on a sample basis for each production lot and provide the test report with the shipment. Hengji Bearing also offers a high speed life test on request.

We recommend that the engineer specify the dn value rather than the RPM alone. A small bearing at a high RPM may have a lower dn value than a large bearing at a moderate RPM, and the grease and clearance requirements follow the dn value. The engineer should also verify that the shield is not being used as a contact seal in a wet environment, because the shield does not keep water out.


Frequently Asked Questions About Shielded Deep Groove Ball Bearings at High Speed

Question 1: Can shielded bearings be used in dusty or wet environments?
Answer: Shielded Deep Groove Ball Bearings can be used in dry dusty environments because the shield blocks large particles from reaching the raceway. They are not suitable for wet environments because the shield has a gap that allows water and fine mist to enter. For wet environments, a contact seal is the correct choice, but the contact seal limits the speed. If the application requires both high speed and wet protection, a different bearing type or an external sealing arrangement should be considered. In our factory, we recommend shielded bearings for dry dust and sealed bearings for wet conditions, and we advise the customer not to exceed the speed rating of the sealed bearing.
Question 2: How is the limiting speed of a shielded bearing determined?
Answer: The limiting speed of a shielded Deep Groove Ball Bearings is determined by the heat generation and the grease life. The manufacturer tests the bearing at increasing speeds and measures the temperature rise and the vibration. The limiting speed is the speed at which the temperature rise reaches the specified limit, typically 40 to 50 degrees Celsius above ambient, or the speed at which the grease life drops below the required value. The limiting speed depends on the bearing size, the cage material, the grease, and the shield design. In our factory, we publish the limiting speed for each bearing model and we recommend that the customer operate below 80 percent of the published value for continuous duty.
Question 3: Can grease be replenished in a shielded bearing during service?
Answer: Grease cannot be replenished in a standard shielded bearing because the shield is pressed into the outer ring and cannot be removed without damaging it. The bearing is lubricated for life. The life of the grease determines the life of the bearing. For high speed applications, the grease life may be shorter than the bearing fatigue life, and the bearing must be replaced when the grease degrades. Some shielded bearings are available with a grease nipple or a removable shield for relubrication, but these are special designs. In our factory, we recommend that the customer select the grease for the expected life and replace the bearing at the recommended interval. We provide the grease life calculation with each high speed order.

Summary for Bearing Application Engineers

Shielded Deep Groove Ball Bearings are ideal for high speed because the non-contact shield eliminates the lip friction that causes contact seals to overheat at high RPM. The shield gap, the grease fill volume, the base oil viscosity, the cage material, and the internal clearance must all be selected for the dn value of the application. The verification should include the clearance measurement, the shield gap measurement, the temperature rise test, and the vibration test. Cixi Hengji Bearing Co., Ltd. has been manufacturing Deep Groove Ball Bearings for over 12 years and provides full high speed selection and verification support for our customers.

Need help selecting or verifying shielded deep groove ball bearings for a high speed application? Contact Cixi Hengji Bearing Co., Ltd. for a free consultation. We will review your dn value and operating conditions and recommend the optimal shield, grease, and clearance configuration.
Previous:No News
Next:No News

Leave Your Message

  • Click Refresh verification code